Support Support Downloads Knowledge Base Case Manager My Juniper Community

Knowledge Base

Search our Knowledge Base sites to find answers to your questions.

Ask All Knowledge Base Sites All Knowledge Base Sites JunosE Defect (KA)Knowledge BaseSecurity AdvisoriesTechnical BulletinsTechnotes Sign in to display secure content and recently viewed articles

Reverting to the Default Factory Configuration for the EX-series Switch

0

0

Article ID: KB11159 KB Last Updated: 11 Aug 2010Version: 4.0
Summary:
There may be a time when you may want or need to default the EX-series switch to factory default settings.  The following information provides you with a number of methods for accomplishing this task.
Symptoms:

Solution:
Reverting to the Default Factory Configuration for the EX-series Switch
If for any reason the current active configuration fails, you can revert to the default factory configuration. You can also rollback to a previous configuration which is covered in other Knowledge Base articles and the EX-series documentation.

The default factory configuration contains the basic configuration settings. This is the first configuration of the switch and it is loaded when the switch is first installed and powered on.

You can revert to the default factory configuration by using the Menu button to the right of the LCD on the front panel of the switch or by using the load factory default configuration command.



Reverting to the Default Factory Configuration by Using the Menu Button
To set the switch to the factory default configuration, use the buttons to the right of the LCD on the front panel of the switch as shown in Figure 1

Figure 1: EX-series Switch Front Panel
LCD panel


Note: If you want to convert an EX 4200 switch from a member of a multimember virtual chassis configuration to a standalone switch, first disconnect the cables connected to the virtual chassis ports (VCPs). See Disconnecting a Virtual Chassis Cable from an EX-series Switch. The Menu button procedure deletes all modified configuration parameters, including virtual chassis parameters such as member ID, mastership priority, and setting of VCP uplinks.
  1. Press the Menu button until you see MAINTENANCE MENU on the panel.

  2. Press the Enter button.

  3. Press Menu until you see FACTORY DEFAULT.

  4. Press Enter. The display says RESTORE DEFAULT?

  5. Press Enter. The screen flashes FACTORY DEFAULT IN PROGRESS and returns to the idle menu. For more information on Idle Menu see EX-series Switch—LCD

Reverting to the Default Factory Configuration by Using the Load Factory Default Command
The load factory default command is a standard JUNOS configuration command and works in the standard way when the command is entered on an EX 3200 switch or on a standalone EX-4200 switch.

When this configuration command is entered on a single EX 4200 switch, it replaces the current active configuration with the default factory configuration. A commit command commits this default factory configuration on the switch.

NOTE:
Any information that had been configured prior to issuing load factory default is deleted, including virtual chassis parameters such as member ID, mastership priority, and setting of VCP uplinks.

However, the load factory default command is not supported on a multimember virtual chassis. If you try to issue a commit command after using load factory default on a virtual chassis that has two or more members, the command fails.

Workaround for switch that was previously included in a multimember virtual chassis
The following workaround allows you to reset factory defaults on a switch that was previously included in a multimember virtual chassis. It deletes all configuration parameters other than the virtual chassis parameters, and allows you to commit the configuration. It does not delete information related to member ID, mastership priority, or settings of VCP uplinks:
  1.  To revert to the factory default configuration type this command in the CLI mode:
    user@switch# load factory default

  2. To enable this default configuration file to run correctly, type this command:
    user@switch# delete system commit factory-settings

  3. Commit the modified default configuration file:
    user@switch# commit


Check the member ID and mastership priority with the show virtual-chassis status command and check to see whether there are remaining settings for uplink VCPs by using the show virtual-chassis vc-port command.

You can remove any remaining virtual chassis parameters, as follows:
  • To change the member ID, use the request virtual-chassis renumber command.
  • To change mastership priority, edit the mastership-priority value.
  • To delete the setting of an uplink VCP, use request virtual-chassis vc-port delete-pic-slot.
Comment on this article > Affected Products Browse the Knowledge Base for more articles related to these product categories. Select a category to begin.

Getting Up and Running with Junos

Getting Up and Running with Junos Security Alerts and Vulnerabilities Product Alerts and Software Release Notices Problem Report (PR) Search Tool EOL Notices and Bulletins JTAC User Guide Customer Care User Guide Pathfinder SRX High Availability Configurator SRX VPN Configurator Training Courses and Videos End User Licence Agreement Global Search